Proportional valves: design and mode of operation
Numerous applications and systems require a highly precise adjustment of the pressure and/or the volume flow to the operating situation. This task is performed by proportional valves.
What are proportional valves?
Unlike switching valves, proportional valves not only assume an open or closed state, but also realize any intermediate positions. The continuous change of state places high demands on the valve design.
In the case of electromagnetic proportional directional valves, electromagnetic actuation systems act on the valve piston and change the opening transverse steps against the return spring and hydraulic forces in proportion to the applied current.
Electromagnetic proportional pressure valves, on the other hand, establish a balance of forces between the actuation system and the hydraulic forces on the effective surfaces via a plug or piston with defined effective surfaces. In this way, pressures can be set, regulated or reduced.
There are three basic types of such proportional valves:
- pressure relief and reducing valves
- directional valves
- flow control valves
These three types are then each divided into further variants of proportional valves. You will also find many of them among our ARGO-HYTOS proportional valves.
Here, in addition to directly controlled proportional directional valves such as the PRM2-04, you can also get pilot operated proportional directional valves such as the PRM8-06.
Direct operated and pilot operated pressure relief valves such as SR1P2-A2 and pressure reducing valves, for example SP4P2-B3, are available for the common ¾ and ⅞ UNF form bores. Proportional flow control valves such as the SF32P-C3/H, among others, are offered as screw-in valves.
How are ARGO-HYTOS proportional valves connected?
We develop all ARGO-HYTOS valves and thus also the proportional valves in different designs:
- as flange-mounted valves in ISO 4401
- as installation valves for UNF - shaped bores
- as sandwich plate valves in ISO4401
- supplementary subplates, manifold plates and pipeline housings
Regulation or control concepts of the ARGO-HYTOS proportional valves
If the controller of the valve receives an input signal, it activates the corresponding solenoid. This then regulates the valve continuously. The regulation or control can be done in three ways:
- without feedback
- with an internal feedback via a slide position sensor
- including external feedback with a closed-loop sensor
Proportional Directional Valves
This variant according to ISO 4401 is available as 4/2 or as 4/3 proportional directional control valve. These valves are available in sizes from DN 04 to DN 10. Each size can regulate two or three volume flow sizes. A pressure compensator can also be used to achieve load-independent volume flow control.
As with many other valves, direct control is typical here. It takes place via poppet or spool elements. We also have pilot-operated valves in our range. In these, the actuator only operates the control stage. The main stage is actuated hydraulically. This principle allows significantly higher hydraulic outputs to be controlled and regulated.
This is impressively demonstrated by the PRM8-06 pilot-operated proportional directional control valve, which is designed for maximum performance. It can handle pressures of up to 350 bar and flow rates of up to 130 liters per minute with a DN-06 size. If you need advanced digital control capabilities in addition to high performance, the PRM9-06 proportional directional control valve, for example, is a good choice.
This valve comes to you with digital onboard electronics including CAN bus communication interface. This makes it ready for the requirements of Industry 4.0.
Proportional pressure relief valves
With pressure relief valves you make a fine adjustment of the maximum pressure in the system. You can also control the valve remotely via a solenoid. For this purpose, our pressure relief valves use the EL6 digital control electronics with DIN plug.
Here, too, we have developed valves with different performance characteristics. They control a flow rate of up to 60 liters per minute - up to a pressure of 350 bar.
Proportional pressure relief valves are offered in versions with rising or falling characteristic. Valves with rising characteristic are characterized by the fact that as the current in the actuating solenoid increases, the system pressure increases proportionally.
In contrast, proportionally operating pressure relief valves with inverse or falling characteristic cause the lowest system pressure through maximum current flow in the actuating solenoid. This is required, for example, for hydraulic fan drives in mobile machinery, as the fan is accelerated to maximum speed in the event of a malfunction.
However, many applications also work with low pressure - above all transmission or clutch controls in mobile equipment. For this purpose, you need adapted proportional pressure reducing valves such as the ARGO-HYTOS PP2P3-W3, which are available from us either directly or pilot operated. The valves are designed for an inlet pressure of up to 50 bar and operate with a maximum control pressure of between 20 and 30 bar.
Solenoids
From ARGO-HYTOS you can get everything from single components to complete system solutions for industrial or mobile hydraulics. For the control of proportional valves or other valves, you often need an electromagnetic actuation system. We have developed our solutions closely adapted to our valves: ARGO-HYTOS actuation systems work as a perfect team with ARGO-HYTOS proportional valves.
For this purpose, the ARGO-HYTOS actuation systems bring ideal properties due to high-precision manufacturing.
Low hysteresis requires minimal friction and precise guidance of the armature. Here, details and high-quality manufacturing with precision in the micrometer range are crucial. Our design with soldered pole tubes, high-quality materials, modern manufacturing processes and comprehensive quality controls ensure you the required precision and thus reliability in all our components.
We think further - and always also about the simplest possible application or maintenance within your systems and processes. Thus, our solenoid coils are also designed for uncomplicated use. The coils of the actuation systems can be rotated around the longitudinal axis, which allows optimal connector positioning. If a coil needs to be replaced, this can be done easily without having to open the hydraulic circuit.
Quality and service from ARGO-HYTOS
Our products are the result of more than 75 years of development work. With our expertise built up over decades, we have grown to become a global leader in the fields of industrial hydraulics and mobile hydraulics.
In addition to technical innovation and perfection, we always attach great importance to personal contact with our customers. This also includes intensive support and advice on all aspects of our products. If you have any questions, please use our online contact or our customer service by phone. We are already looking forward to giving you competent advice in a personal meeting!